1/3/2024 0 Comments 4000d airflow![]() ![]() A Look at the Front I/OĪ budget case is going to show its stripes in places, and the loadout of ports is one of them here. Like in most cases, however, the vertical-mounting hardware and the necessary GPU riser cable are not included you'll have to find these yourself. The rear panel has two slots for vertical GPU mounting alongside the seven PCI Express card positions. In most such case designs, the supply gets isolated and has to fend for itself in terms of air through the bottom panel. This should help to keep the power supply relatively cool. Unlike on most rival cases, though, the metal sheet separating these two areas is covered in the same triangular perforations seen on the front of the case. The upper compartment holds the motherboard, whereas the lower compartment is walled off behind a shroud that holds the power supply and has room for storage devices. Like many other modern chassis, the 4000D Airflow is broken up into two main compartments. On the inside of the case, the perforations continue. This shouldn't hamper cooling much, however, due to the abundance of ventilation elsewhere and the front-to-back design. The right panel is a solid sheet of steel, and the left panel is tempered glass, without any cut-throughs for air to flow in or out on either side. The two sides of the chassis aren't quite as friendly in the airflow department. Two 120mm Corsair AirGuide fans are pre-mounted (one front, one back) to push things along. Altogether, this makes for a clear path of low resistance for air to pass straight through the case. The top is also perforated and covered by a large magnetic dust filter, and the back of the case has ventilation holes cut in it from top to bottom. In addition to incorporating that perforated front panel, Corsair also left large gaps on either side of this perforated section that permit additional inward ventilation. The "Airflow" in the name is no idle boast. ![]() But its affordability and construction quality make it worth a look if you're shopping for a spiffy-on-a-budget PC case while saving up for the stuff inside. Priced at a low $79.99 with a tempered-glass side panel, it's far from the most feature-packed ATX mid-tower we've seen for under $100. Best Malware Removal and Protection Softwareįeaturing a front panel covered in triangle perforations, Corsair's 4000D Airflow PC case has a distinctive-looking face and delivers what it promises: ample, well, airflow to keep your PC components cool under pressure.But as I'm going to be filling the case with fans either way, I want to see what other people think of the potential airflow differences of the cases. Overall I'm thinking of getting the NR600. I also looked in to another case at a similar price point, the Corsair 4000D airflow, I feel like it could probably fit it, but I don't think I like the bare bones'ness of the case, even if it does look pretty good. The P400A also has 3 intake fans but it has absolutely no way of fitting a radiator at the top. The NR600 has 3 fans in the front and MIGHT fit the thick 240mm cooler at the top, although most likely not. Now, the issue is that when I get a new GPU, I want it to have good airflow as well, I know the Meshify C Mini is good build quality, but it only has 2 front intake fans that would be taken up by the 240mm cooler, as I'd probably be unable to place it up top. I'm going to be using a very thick 240mm AIO radiator for my CPU cooler (65mm including the fans), and so need enough space to either top mount it (best case scenario, pun intended.) or at least front mount it. (Fans will be a mixture of Be Quiet Silent Wings 3 from my previous case and Arctic P12's from the AIO.) Which would be certainly annoying as I'm basically filling the case with fans. Issue is, I need to chose one of these cases (as they're pretty much the same in terms of cost) that provide me with not only ample amount of airflow, but also are easy to build in.Ī reviewer I've watched said that the P400A has relatively poor cable management for the front intake fans, as the only hole that let's them go through the back and to the motherboard is through the hole where the front I/O cables go through. I've recently gotten in to a rabbit hole of choosing a case.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |